Dell Networking S6000 System Reference Manual Download

Page: 207 / 1510

fragments

Enter the keyword

fragments

to use ACLs to control packet

fragments.

Defaults

Not configured

Command
Modes

CONFIGURATION-EXTENDED-ACCESS-LIST

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.3.1.0

Add the DSCP value for ACL matching.

Version 8.2.1.0

Allows ACL control of fragmented packets for IP (Layer 3)
ACLs.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 7.4.1.0

Added support for the non-contiguous mask and added the

monitor

option. Deprecated the keyword

established

Version 6.5.10

Expanded to include the optional QoS

order

priority for the

ACL entry.

Usage
Information

The

monitor

option is relevant in the context of flow-based monitoring only. For

more information, refer to

Port Monitoring

The

order

option is relevant in the context of the Policy QoS feature only. The

following applies:

• The

seq

sequence-number

command is applicable only in an ACL group.

• The

order

option works across ACL groups that have been applied on an

interface via the QoS policy framework.

• The

order

option takes precedence over

seq

sequence-number

• If

sequence-number

is not configured, the rules with the same order value are

ordered according to their configuration order.

• If

sequence-number

is configured, the sequence-number is used as a tie

breaker for rules with the same order.

Access Control Lists (ACL)

207

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands