Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 680 / 1510

background image

Line

Description

TX Power Low
Warning threshold

Factory-defined setting. Value can differ between SFP and
SFP+.

Power Low
Warning threshold

Factory-defined setting. Value can differ between SFP and
SFP+.

Temperature

Current temperature of the SFPs. If this temperature crosses
Temp High alarm/warning thresholds, the temperature high
alarm/warning flag is set to true.

Voltage

Current voltage of the SFPs. If this voltage crosses voltage
high alarm/warning thresholds, the voltage high alarm/
warning flag is set to true.

Tx Bias Current

Present transmission (Tx) bias current of the SFP. If this
crosses bias high alarm/warning thresholds, the TX bias high
alarm/warning flag is set to true. If it falls below the low
alarm/warning thresholds, the TX bias low alarm/warning
flag is set to true.

Tx Power

Present Tx power of the SFP. If this crosses Tx power alarm/
warning thresholds, the Tx power high alarm/warning flag is
set to true. If it falls below the low alarm/warning
thresholds, the Tx power low alarm/ warning flag is set to
true.

Rx Power

Present receiving (Rx) power of the SFP. This value is either
average Rx power or OMA. This depends on the Rx Power
measurement type displayed above. If this crosses Rx power
alarm/warning thresholds, the Rx power high alarm/warning
flag is set to true. If it falls below the low alarm/warning
thresholds, the Rx power low alarm/warning flag is set to
true.

Data Ready state
Bar

This field indicates that the transceiver has achieved power
up and data is ready. This is set to true if data is ready to be
sent and set to false if data is being transmitted.

Rx LOS state

This is the digital state of the Rx_LOS output pin. This is set
to true if the operating status is down.

Tx Fault state

This is the digital state of the Tx Fault output pin.

Rate Select state

This is the digital state of the SFP rate_select input pin.

RS state

This is the reserved digital state of the pin AS(1) per
SFF-8079 and RS(1) per SFF-8431.

Tx Disable state

If the admin status of the port is down then this flag is set to
true.

Temperature High
Alarm Flag

This can be either true or false, depending on the Current
voltage value displayed above.

680

Interfaces

«
...
678
679
680
681
682
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: E-Trailer Pages: 8

Brand: 4O3A Pages: 2

Brand: Cables to Go Pages: 4

Brand: Aube Technologies Pages: 118

Brand: HMS Networks Pages: 16

Brand: A-Neuvideo Pages: 16

Brand: Black Box Pages: 9

Brand: PRO SIGNAL Pages: 2

Liquipoint FTW33

Brand: Endress+Hauser Pages: 48

Brand: Ubiquiti Pages: 14

Brand: H-Tronic Pages: 15

Brand: Pakedge Device & Software Pages: 14

Smatrix Wave Plus Uahome Module R-167

Brand: Uponor Pages: 48

kontron KSwitch D3 UMP

Brand: S&T Pages: 36

Brand: Extron electronics Pages: 6

Brand: Epcom Pages: 2

Brand: 3Com Pages: 104

CONNECTION PERFECTION 32797

Brand: Lindy Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands