manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1402 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1402

Version 7.5.1.0

Introduced on the C-Series.

pre-Version 
6.2.1.1

Introduced on the E-Series.

Related 
Commands

forward-delay

 — changes the wait time before STP transitions to the Forwarding 

state.

hello-time

 — changes the time interval between BPDUs.

protocol spanning-tree

To enable and configure the spanning tree group, enter SPANNING TREE mode.

S6000

Syntax

protocol spanning-tree 

stp-id

To disable the Spanning Tree group, use the 

no protocol spanning-tree 

stp-id

 command.

Parameters

stp-id

Enter zero (0). Dell Networking OS supports one spanning 
tree group, group 0.

Defaults

Not configured.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version 
6.2.1.1

Introduced on the E-Series.

1402

Spanning Tree Protocol (STP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments