Dell Networking S6000 System Reference Manual Download

Page: 495 / 1510

UCAST 0 0

UCAST 1 0

UCAST 2 0

UCAST 3 0

UCAST 4 0

UCAST 5 0

UCAST 6 0

UCAST 7 0

UCAST 8 0

UCAST 9 0

UCAST 10 0

UCAST 11 0

Dell#

To identify the port that is congested and monitor all the priority groups on that
particular port:

Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0

resource port 1 prio all

Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0)

---------------------------------------

PG# SHARED CELLS HEADROOM CELLS

---------------------------------------

0 0 0

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

Dell#

To determine the specific priority group, unicast or multicast queue that is
congested and monitor that queue separately:

Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0

resource port 1 prio 6

Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0)

---------------------------------------

PG# SHARED CELLS HEADROOM CELLS

---------------------------------------

6 0 0

dcb pfc-total-buffer-size

Configure the total buffer size for PFC in kilobytes. This utility is supported on the S6000 platform.

S6000

Syntax

dcb pfc-total—buffer—size

Parameters

Enter a number in the range of 0 to 7787.

Data Center Bridging (DCB)

495

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands