Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 386 / 1510

background image

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage
Information

Loopback interfaces are up constantly and the BGP session may need one
interface constantly up to stabilize the session. The

neighbor update-source

command is not necessary for directly connected internal BGP sessions.
Neighbors are sorted according to the source and destination ip addresses. If an
update-source ip address exists, then the source ip address determines the order in
which the neighbors are displayed.

neighbor weight

Assign a weight to the neighbor connection, which is used to determine the best path.

S6000

Syntax

neighbor {

ip-address

|

peer-group-name

} weight

weight

To remove a weight value, use the

no neighbor {

ip-address

|

peer-

group-name

} weight

command.

Parameters

ip-address

Enter the IP address of the peer router in dotted decimal
format.

peer-group-
name

Enter the name of the peer group to disable all routers within
the peer group.

weight

Enter a number as the weight. The range is from 0 to 65535.
The default is

0

.

Defaults

0

Command
Modes

ROUTER BGP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

386

Border Gateway Protocol

«
...
384
385
386
387
388
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Water Witch Pages: 2

Brand: Magnetrol Pages: 12

Brand: Magnimage Pages: 53

VEEMUX SM-nXm-15V-LC

Brand: Network Technologies Pages: 46

QuantaMesh T4000 Series

Brand: QCT Pages: 41

Brand: DirectConnect Pages: 10

Brand: Phonocar Pages: 2

Brand: HDTV Supply Pages: 15

Brand: S&S Northern Pages: 8

Brand: Black Box Pages: 20

iBootBar iBB-DC8

Brand: Dataprobe Pages: 36

Brand: Cabletron Systems Pages: 56

IES2016-16T Series

Brand: 3onedata Pages: 3

Brand: Enterasys Pages: 41

Brand: Ocean Matrix Pages: 6

Brand: Kramer Pages: 8

Brand: KinAn Pages: 8

Brand: Scion-Tech Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands