Dell Networking S6000 System Reference Manual Download

Page: 1487 / 1510

Related
Commands

vxlan-instance

- Enable VXLAN Instance configuration on the platform.

show running-config vxlan

Displays the configuration information of the VXLAN on S6000.

S6000

Syntax

show running-config vxlan

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

Version 9.4.
(0.0)

Introduced on the S6000.

Example

Dell#show running-config vxlan

feature vxlan

vxlan-instance 1

gateway-ip 3.3.3.3

fail-mode secure

controller 1 192.168.122.6 port 6632 ssl

no shutdown

Related
Commands

vxlan-instance

- Enable VXLAN Instance configuration on the platform.

show vxlan vxlan-instance unicast-mac-remote

Displays the information of the remote unicast MACs associated with the logical network related to

Network Virtualization Overlay (NVO) Gateway.

S6000

Syntax

show vxlan vxlan-instance

instance ID

unicast-mac-remote

[logical-network

name

| vnid

VNID

]

Parameters

instance ID

Enter the VXLAN instance ID. The platform supports only the
instance ID

in the initial release.

Virtual Extensible LAN (VXLAN)

1487

«
...
1485
1486
1487
1488
1489
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands