manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 468 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 468

0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf 

TLV Pkts

0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco 

TLV Pkts

Dell(conf-qos-policy-out-ets)#do sho int te 0/3 ets de

Interface TenGigabitEthernet 0/3

Max Supported TC Groups is 4

Number of Traffic Classes is 8

Admin mode is on

Admin Parameters :

------------------

Admin is enabled

TC-grp Priority#   Bandwidth TSA

------------------------------------------------

0                  -         -

1      0,1,2       100%      ETS

2      3           0 %       SP

3      4,5,6,7     0 %       SP

4                  -         -

5                  -         -

6                  -         -

7                  -         -

Remote Parameters :

-------------------

Remote is disabled

Local Parameters :

------------------

Local is enabled

TC-grp Priority#   Bandwidth TSA

------------------------------------------------

0                  -         -

1      0,1,2       100%      ETS

2      3           0 %       SP

3      4,5,6,7     0 %       SP

4                  -         -

5                  -         -

6                  -         -

7                  -         -

Oper status is init

ETS DCBX Oper status is Down

State Machine Type is Asymmetric

Conf TLV Tx Status is enabled

Reco TLV Tx Status is enabled

0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf 

TLV Pkts

0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco 

TLV Pkts

Dell(conf)# show interfaces tengigabitethernet 0/0 ets detail

Interface TenGigabitEthernet 0/0

Max Supported TC Groups is 4

Number of Traffic Classes is 8

Admin mode is on

Admin Parameters :

------------------

468

Data Center Bridging (DCB)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments