Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 431 / 1510

background image

holdtime

Enter a number for the time interval, in seconds, between
the last keepalive message and declaring the router dead.
The range is from 3 to 65535. The default is

180 seconds

.

Defaults

none

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Version 7.6.1.0

Introduced on the E-Series.

MBGP Commands

Multiprotocol BGP (MBGP) is an enhanced BGP that enables multicast routing policy throughout the

internet and connecting multicast topologies between BGP and autonomous systems (ASs).
Dell Networking OS MBGP is implemented as per IETF RFC 1858.

BGPv4 is supported in the following:

Dell Networking
OS Version

Platform Support

7.8.1.0, MBGP for
IPv4 Multicast Only

S-Series

debug ip bgp dampening

View information on routes being dampened.

S6000

Syntax

debug ip bgp [vrf test | ipv4 {unicast | multicast} | ipv6
{unicast | multicast} dampening

Border Gateway Protocol

431

«
...
429
430
431
432
433
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Underwater Switch 24V DC/DMX/02

Brand: Oase Pages: 40

Brand: AVLT-Power Pages: 12

EdgePoint EP-S16

Brand: Ubiquiti Pages: 22

RMQ-Titan M22-LED Series

Brand: Eaton Pages: 4

Brand: Microsens Pages: 8

Brand: C&H Technologies Pages: 28

N.JGS516PE-100EUS

Brand: Duxbury Networking Pages: 4

Brand: Aruba Networks Pages: 40

Brand: Nortel Pages: 46

Brand: IOGear Pages: 10

Brand: TRENDnet Pages: 2

Brand: Exsys Pages: 16

Brand: AMERITRON Pages: 16

Brand: Honeywell Home Pages: 4

Brand: SMART-AVI Pages: 2

IP-Watcher 2x2 Digital PoE

Brand: W&T Pages: 79

Essentials EXP-SW-0401-H2

Brand: Wyrestorm Pages: 2

PROSAFE RKSE Series

Brand: Guardmaster Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands