Dell Networking S6000 System Reference Manual Download

Page: 1318 / 1510

Related
Commands

show protocol-tunnel

— displays tunneling information for all VLANs.

show running-config

— displays the current configuration.

show protocol-tunnel

Display protocol tunnel information for all or a specified VLAN-Stack VLAN.

S6000

Syntax

show protocol-tunnel [vlan

vlan-id

]

Parameters

vlan

vlan-id

(OPTIONAL) Enter the keyword

vlan

then the VLAN ID to

display information for the one VLAN. The range is from 1 to
4094.

Defaults

none

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.2.1.0

Introduced on the C-Series, E-Series and E-Series ExaScale.

Version 7.4.1.0

Introduced

Example

Dell#show protocol-tunnel

System Rate-Limit: 75 frames/second

VLAN Protocols Interface

1000 STP,PVST Gi 5/7,Gi 5/6

1001 LLDP,GVRP Gi 5/7,Gi 5/6

1002 MMRP,MVRP Gi 5/7,Gi 5/6

1003 LACP,DOT1X Gi 5/7,Gi 5/6

1004 OAM,PAUSE Gi 5/7,Gi 5/6

1005 E-LMI Gi 5/7,Gi 5/6

Example
(Specific VLAN)

Dell#show protocol-tunnel vlan 2

System Rate-Limit: 1000 Frames/second

Interface Vlan Protocol(s)

1318

Service Provider Bridging

«
...
1316
1317
1318
1319
1320
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands