Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 200 / 1510

background image

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.3.1.0

Added the keyword

dscp

.

Version 8.2.1.0

Allows ACL control of fragmented packets for IP (Layer 3)
ACLs.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 7.4.1.0

Added support for non-contiguous mask and added the

monitor

option. Deprecated the keyword

established

.

Version 6.5.10

Expanded to include the optional QoS

order

priority for the

ACL entry.

Usage
Information

The

order

option is relevant in the context of the Policy QoS feature only. For

more information, refer to the “Quality of Service” chapter of the

Dell Networking

OS Configuration Guide

.

NOTE: When ACL logging and byte counters are configured simultaneously,
byte counters may display an incorrect value. Configure packet counters with
logging instead.

When you use the

log

option, the CP processor logs details about the packets that

match. Depending on how many packets match the log entry and at what rate, the
CP may become busy as it has to log these packets’ details.

The S-Series cannot count both packets and bytes; when you enter the count byte
options, only bytes are incremented.

The

monitor

option is relevant in the context of flow-based monitoring only. For

more information, refer to

Port Monitoring

.

Most ACL rules require one entry in the CAM. However, rules with TCP and UDP
port operators (for example, gt, lt, or range) may require more than one entry. The
range of ports is configured in the CAM based on bit mask boundaries; the space
required depends on exactly what ports are included in the range.

200

Access Control Lists (ACL)

«
...
198
199
200
201
202
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: DANLERS Pages: 2

Brand: H3C Pages: 55

Brand: H3C Pages: 111

Brand: H3C Pages: 34

Brand: H3C Pages: 47

Brand: H3C Pages: 8

Brand: H3C Pages: 47

Brand: H3C Pages: 4

S5560X-EI Series

Brand: H3C Pages: 63

S5560X-EI Series

Brand: H3C Pages: 89

Brand: H3C Pages: 3

S12500G-AF Series

Brand: H3C Pages: 86

Brand: H3C Pages: 168

Brand: H3C Pages: 56

Brand: H3C Pages: 19

Brand: H3C Pages: 4

Brand: H3C Pages: 36

Brand: Pakedge Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands