Dell Networking S6000 System Reference Manual Download

Page: 791 / 1510

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

Usage
Information

To prevent the link state database from receiving incorrect routing information
from unauthorized routers, use the

area-password

command on routers within

an area.

The configured password injects into Level 1 LSPs, CSNPs, and PSNPs.

Related
Commands

•

domain-password

— allows you to set the authentication password for a

routing domain.

•

isis password

— allows you to configure an authentication password for an

interface.

clear config

Clear IS-IS configurations that display under the

router isis

heading of the

show running-config

command output.

S6000

Syntax

clear config

Command
Modes

ROUTER ISIS

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.1

Introduced on the S4810.

Usage
Information

CAUTION: Use caution when you enter this command. Back up your
configuration prior to using this command or your IS-IS configuration will
be erased.

Intermediate System to Intermediate System (IS-IS)

791

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands