Dell Networking S6000 System Reference Manual Download Page 320

Page: 320 / 1510

Related
Commands

interface_management_ethernet_ip_address

— Assign an IP address to the

Management Ethernet interface.

reload

— Configure speed, duplex, and negotiation settings for the management

interface.

show serial console baud rate

Use the show serial console to show the values of the serial console baud rate.

S6000

Syntax

show serial console baudrate

Command
Modes

BOOT_USER

Command
History

Version 9.0.2.0

Introduced on the S6000.

Example

BOOT_USER # show serial console baudrate

Serial console baudrate = 9600

watchdog <string>

Enable the watchdog timer, when the enabled watchdog timer is set to 60 seconds.

S6000

Syntax

enable

disable

status

timeout

settimeout

watchdog timer

Parameters

enable

Enter the keyword

enable

to enable the watchdog.

disable

Enter the keyword

disable

to disable the watchdog.

status

Enter the keyword

status

to see the watchdog status.

timeout

Enter the keyword

timeout

to see the timeout configured for

the watchdog.

settimeout

Enter the keyword

set timeout

to set timeout.

320

Boot Command Line Interface

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 320 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: