manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1190 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1190

variable

Enter the MIB object to monitor. The variable must be in the 
SNMP OID format; for example, 1.3.6.1.2.1.1.3. The object 
type must be a 32-bit integer.

interval

Time, in seconds, the alarm monitors the MIB variables; this 
is the alarmSampleType in the RMON alarm table. The range 
is from 5 to 3600 seconds.

delta

Enter the keyword 

delta

 to test the change between MIB 

variables. This is the alarmSampleType in the RMON alarm 
table.

absolute

Enter the keyword 

absolute

 to test each MIB variable 

directly. This is the alarmSampleType in the RMON alarm 
table.

rising-
threshold 

value 

event-number

Enter the keywords 

rising-threshold

 then the value (32 

bit) the rising-threshold alarm is either triggered or reset. 
Then enter the event-number to trigger when the rising 
threshold exceeds its limit. This value is the same as the 
alarmRisingEventIndex or alarmTable of the RMON MIB. If 
there is no corresponding rising-threshold event, the value is 
zero.

falling-
threshold 

value 

event-number

Enter the keywords 

falling-threshold

 then the value (32 

bit) the falling-threshold alarm is either triggered or reset. 
Then enter the event-number to trigger when the falling 
threshold exceeds its limit. This value is the same as the 
alarmFallingEventIndex or the alarmTable of the RMON MIB. 
If there is no corresponding falling-threshold event, the value 
is zero.

owner 

string

(OPTIONAL) Enter the keyword 

owner

 then the owner name 

to specify an owner for the alarm. This is the alarmOwner 
object in the alarmTable of the RMON MIB.

Defaults

owner

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

1190

Remote Monitoring (RMON)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments