Dell Networking S6000 System Page 607 Reference Manual Download

Page: 607 / 1510

interface

interface

Enter the following keywords and slot/port or number
information:

• For a 1-Gigabit Ethernet interface, enter the keyword

gigabitethernet

followed by the slot/port

information.

• For a Port Channel interface, enter the keyword

port-

channel

then a number. The range is from 1 to 128.

• For a 10–Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

Defaults

Disabled.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

E-Series legacy
command

Usage
Information

IGMP commands accept

only

non-VLAN interfaces — specifying VLAN does not

yield results. This command displays packets for IGMP and IGMP snooping.

ip igmp access-group

To specify access control for packets, use this feature.

S6000

Syntax

ip igmp access-group

access-list

To remove the feature, use the

no ip igmp access-group access-list

command.

Internet Group Management Protocol (IGMP)

607

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands