manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1435

53

VLAN Stacking

With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you 

can “stack” VLANs into one tunnel and switch them through the network transparently.
The Dell Networking operating software supports this feature on the S6000 platform.

For more information about basic VLAN commands, refer to the 

Virtual LAN (VLAN) Commands

 section in 

the 

Layer 2

 chapter.

Important Points to Remember

• If you do not enable the spanning tree protocol (STP) across the stackable VLAN network, STP bridge 

protocol data units (BPDUs) from the customer’s networks are tunneled across the stackable VLAN 

network.

• If you do enable STP across the stackable VLAN network, STP BPDUs from the customer’s networks 

are consumed and not tunneled across the stackable VLAN network unless you enable protocol 

tunneling.

NOTE: For more information about protocol tunneling on the E-Series, refer to 

Service Provider 

Bridging

.

• Layer 3 protocols are not supported on a stackable VLAN network.
• Assigning an IP address to a stackable VLAN is supported when all the members are only stackable 

VLAN trunk ports. IP addresses on a stackable VLAN-enabled VLAN are not supported if the VLAN 

contains stackable VLAN access ports. This facility is provided for the simple network management 

protocol (SNMP) management over a stackable VLAN-enabled VLAN containing only stackable VLAN 

trunk interfaces. Layer 3 routing protocols on such a VLAN are not supported.

• Dell Networking recommends that you do not use the same MAC address, on different customer 

VLANs, on the same stackable VLAN.

• Interfaces configured using stackable VLAN access or stackable VLAN trunk commands do not switch 

traffic for the default VLAN. These interfaces are switch traffic only when they are added to a non-

default VLAN.

• Starting with Dell Networking OS version 7.8.1 for C-Series and S-Series (Dell Networking OS version 

7.7.1 for E-Series, 8.2.1.0 for E-Series ExaScale), a vlan-stack trunk port is also allowed to be 

configured as a tagged port and as an untagged port for single-tagged VLANs. When the vlan-stack 

trunk port is also a member of an untagged vlan, the port must be in Hybrid mode. Refer to 

portmode 

hybrid

.

VLAN Stacking

1435

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands