Dell Networking S6000 System Reference Manual Download

Page: 51 / 1510

PREFIX-LIST Mode

To configure a prefix list, use PREFIX-LIST mode.
To enter PREFIX-LIST mode:

Verify that you are logged in to CONFIGURATION mode.

Enter the

ip prefix-list

command. Include a name for the prefix list. The prompt changes to

include (conf-nprefixl).

You can return to CONFIGURATION mode by using the

exit

command.

PROTOCOL GVRP Mode

To enable and configure GARP VLAN Registration Protocol (GVRP), use PROTOCOL GVRP mode. For
more information, refer to

GARP VLAN Registration (GVRP)

To enter PROTOCOL GVRP mode:

Verify that you are logged in to CONFIGURATION mode.

Enter the

protocol gvrp

command. The prompt changes to include (config-gvrp).

You can return to CONFIGURATION mode by using the

exit

command.

RAPID SPANNING TREE (RSTP) Mode

To enable and configure RSTP, use RSTP mode. For more information, refer to

Rapid Spanning Tree

Protocol (RSTP)

To enter RSTP mode:

Verify that you are logged in to CONFIGURATION mode.

Enter the

protocol spanning-tree rstp

command. The prompt changes to include (conf-rstp).

You can return to CONFIGURATION mode by using the

exit

command.

ROUTE-MAP Mode

To configure a route map, use ROUTE-MAP mode.
To enter ROUTE-MAP mode:

Verify that you are logged in to CONFIGURATION mode.

Use the

route-map

map-name

[permit | deny] [

sequence-number

]

command. The prompt

changes to include (config-route-map).

You can return to CONFIGURATION mode by using the

exit

command.

ROUTER BGP Mode

To enable and configure Border Gateway Protocol (BGP), use ROUTER BGP mode. For more information,
refer to

Border Gateway Protocol IPv4 (BGPv4)

To enter ROUTER BGP mode:

Verify that you are logged in to CONFIGURATION mode.

CLI Basics

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands