Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1266 / 1510

background image

• For the Null interface, enter the keywords

null 0

.

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a ten-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For VLAN interface, enter the keyword

vlan

then a

number from 1 to 4094.

Defaults

Not configured.

Command
Modes

TACACS SERVER GROUP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.4.
(0.0)

Introduced on the S-Series and Z-Series.

Usage
Information

You can use this command to associate a group of TACACS servers with a VRF and
source interface. You can configure the source interface only with the VRF
attribute and source interface is optional with the VRF attributes.

If VRF is not configured on the TACACS group, then the group is considered to be
on the default VRF.

RADIUS groups and VRFs have one-to-one mapping. If a VRF is configured with
one RADIUS group, then you cannot use the same VRF with another RADIUS
group. When the VRF is removed, then the corresponding RADIUS group is also
removed automatically.

Example

Dell(conf)#tacacs-server group group1

Dell(conf-tacacs-group)#tacacs-server vrf vrf1 source-

interface tengigabitethernet 0/36

Dell(conf)#tacacs-server group group2

Dell(conf-tacacs-group)#tacacs-server vrf default

Port Authentication (802.1X) Commands

An authentication server must authenticate a client connected to an 802.1X switch port. Until the
authentication, only Extensible Authentication Protocol over LAN (EAPOL) traffic is allowed through the

1266

Security

«
...
1264
1265
1266
1267
1268
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

BNI IOL-314-S52-P012

Brand: Balluff Pages: 22

Brand: Camozzi Pages: 2

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Brand: Jabra Pages: 4

Brand: Zigen Pages: 40

Brand: Zigen Pages: 4

Brand: Vector Pages: 6

Brand: Holland Pages: 4

Cooper Power Systems LCR 6200 RFN

Brand: Eaton Pages: 8

Brand: Free-Way Switch Pages: 6

Brand: Net Generation Pages: 38

Universal Videohub 288

Brand: Blackmagicdesign Pages: 107

Brand: Black Box Pages: 2

SmartSTACK ELS100-24TXG

Brand: Cabletron Systems Pages: 7

Brand: Yacoub Automation GmbH Pages: 45

Brand: HighSecLabs Pages: 4

TIMEGUARD IS3N-20

Brand: Theben Pages: 2

Brand: Monoprice Pages: 4

Brand: GearMo Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands