Dell Networking S6000 System Reference Manual Download Page 724

Page: 724 / 1510

Dell Networking OS does not support sending DNS queries over a VLAN. DNS
queries are sent out all other interfaces, including the Management port.

To view current bindings, use the

show hosts

command.

Related
Commands

ip name-server

— specifies a DNS server.

show hosts

— Views the current bindings.

ip domain-name

Configure one domain name for the switch.

S6000

Syntax

ip domain-name

name

To remove the domain name, use the

no ip domain-name

command.

Parameters

name

Enter one domain name to be used to complete unqualified
names (that is, incomplete domain names that cannot be
resolved).

Defaults

Not configured.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

724

IPv4 Routing

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 724 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: