Dell Networking S6000 System Reference Manual Download

Page: 1123 / 1510

Defaults

none

Command
Modes

CLASS-MAP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Usage
Information

To access this command, enter the

class-map

command. After the class map is

identified, you can configure the match criteria.

Related
Commands

class-map

— identifies the class map.

match mac dot1p

Configure a match criterion for a class map based on a dot1p value.

S6000

Syntax

match mac dot1p {dot1p-list}

Parameters

dot1p-list

Enter a dot1p value. The range is from 0 to 7.

Defaults

none

Command
Modes

CLASS-MAP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Quality of Service (QoS)

1123

«
...
1121
1122
1123
1124
1125
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands