manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1028

    Number of TOS metric: 0

       TOS 0 Metric: 1

  Link connected to: a Transit Network

    (Link ID) Designated Router address: 192.68.142.2

    (Link Data) Router Interface address: 192.68.142.2

    Number of TOS metric: 0

       TOS 0 Metric: 1

  Link connected to: a Transit Network

    (Link ID) Designated Router address: 192.68.141.2

    (Link Data) Router Interface address: 192.68.141.2

    Number of TOS metric: 0

       TOS 0 Metric: 1

  Link connected to: a Transit Network

    (Link ID) Designated Router address: 192.68.140.2

    (Link Data) Router Interface address: 192.68.140.2

    Number of TOS metric: 0

       TOS 0 Metric: 1

Link connected to: a Stub Network

    (Link ID) Network/subnet number: 11.1.5.0

--More--

Related 
Commands

show ip ospf database

 — displays OSPF database information.

show ip ospf database summary

Display the network summary (type 3) LSA routing information.

S6000

Syntax

show ip ospf [

process-id

 | vrf 

vrf-name

] database summary 

[

link-state-id

] [adv-router 

ip-address

]

Parameters

process-id

Enter the OSPF Process ID to show a specific process. If no 
Process ID is entered, command applies only to the first 
OSPF process.

vrf 

vrf-name

Enter the keyword 

vrf

 followed by the name of the VRF to 

view LSA routing information corresponding to the OSPF 
process that is tied to a specific VRF.

link-state-id

(OPTIONAL) Specify LSA ID in dotted decimal format. The 
LSA ID value depends on the LSA type, and it can be one of 
the following:

• the network’s IP address for Type 3 LSAs or Type 5 LSAs
• the router’s OSPF router ID for Type 1 LSAs or Type 4 

LSAs

• the default destination (0.0.0.0) for Type 5 LSAs

adv-router 

ip-

address

(OPTIONAL) Enter the keywords 

adv-router

 then the IP 

address of an Advertising Router to display only the LSA 
information about that router.

1028

Open Shortest Path First (OSPFv2 and OSPFv3)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands