Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1010 / 1510

background image

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.4.
(0.0)

Added support for VRF.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Added support of Multi-Process OSPF.

Version 7.8.1.0

Added the

process-id

option, in support of Multi-Process

OSPF.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series and E-Series.

Usage
Information

To isolate problems with external routes, use this command. In OSPF, external
routes are calculated by adding the LSA cost to the cost of reaching the ASBR
router. If an external route does not have the correct cost, use this command to
determine if the path to the originating router is correct. The display output is not
sorted in any order.

NOTE: ASBRs that are not in directly connected areas are also displayed.

You can determine if an ASBR is in a directly connected area (or not) by the flags.
For ASBRs in a directly connected area, E flags are set. In the following example,
router 1.1.1.1 is in a directly connected area since the Flag is E/-/-/. For remote
ASBRs, the E flag is clear (-/-/-/).

Example

Dell#show ip ospf 1asbr

RouterID Flags Cost Nexthop Interface Area

3.3.3.3 -/-/-/ 2 10.0.0.2 Gi 0/1 1

1.1.1.1 E/-/-/ 0 0.0.0.0 - 0

Dell#

show ip ospf database

Display all LSA information. If you do not enable OSPF on the switch, no output is generated.

S6000

Syntax

show ip ospf

process-id

[vrf

vrf-name

] database [database-

summary]

1010

Open Shortest Path First (OSPFv2 and OSPFv3)

«
...
1008
1009
1010
1011
1012
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Datavideo Pages: 58

Brand: Cole Hersee Pages: 2

Brand: Yamamoto Electric Works Co., Ltd. Pages: 15

Brand: AVLT-Power Pages: 12

Brand: ATEN Pages: 17

Brand: Grizzly Pages: 2

Brand: Extron electronics Pages: 6

24/48 10/100 Ports + 2GE

Brand: Accton Technology Pages: 512

Brand: H-Tronic Pages: 36

3CR17342-91 - Switch 4210 PWR

Brand: 3Com Pages: 8

Brand: Zenith Pages: 22

Brand: Digi Pages: 21

60-774 - Security SuperBus 2000 8-Zone Input Module

Brand: ITI Pages: 8

Brand: Metel Pages: 11

UltraConsole Remote UCR-1R1X04U

Brand: Rose electronics Pages: 2

UltraConsole UC1-1X16U

Brand: Rose electronics Pages: 2

Brand: Dell Pages: 201

Brand: Pulsar Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands