Dell Networking S6000 System Reference Manual Download Page 796

Page: 796 / 1510

Version
8.3.12.0

Introduced on the S4810.

Version 6.3.1.0

Introduced.

debug isis snp-packets

To debug IS-IS complete sequence number PDU (CSNP) and partial sequence number PDU (PSNP)

packets, enable debugging on a specific interface and provides diagnostic information.

S6000

Syntax

debug isis snp-packets [

interface

]

To turn off debugging, use the

no debug isis snp-packets [

interface

]

command.

Parameters

interface

(OPTIONAL) Identifies the interface type slot/port as one of
the following:

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a Gigabit Ethernet interface, enter the keyword

GigabitEthernet

then the slot/port information.

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a VLAN, enter the keyword

vlan

then a number from

1 to 4094.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.2(0.2)

Introduced on the Z9000.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

796

Intermediate System to Intermediate System (IS-IS)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 796 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: