manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1491 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1491

Version 9.4.
(0.0)

Introduced on the S6000.

Example

Dell#show vxlan vxlan-instance 1 physical-locator

Instance : 1

Tunnel   : count 1

    36.1.1.1 : vxlan_over_ipv4 (up)

Related 
Commands

vxlan-instance

- Enable VXLAN Instance configuration on the platform.

show vxlan vxlan-instance logical network

Displays logical network information related to Network Virtualization Overlay (NVO) Gateway.

S6000

Syntax

show vxlan vxlan-instance 

instance ID

 logical-network [name 

name

]

Parameters

instance ID

Enter the VXLAN instance ID. The platform supports only the 
instance ID 

1

 in the initial release.

name 

name

(OPTIONAL) Enter the keyword 

name

 and enter the name of 

VXLAN logical network up to a length of maximum 30 
characters.

Command 
Modes

• EXEC
• EXEC Privilege

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

Version 9.4.
(0.0)

Introduced on the S6000.

Example

Dell#show vxlan vxlan-instance 1 logical-network

Instance        : 1

Total LN count  : 1

  Name                                                     VNID

  bffc3be0-13e6-4745-9f6b-0bcbc5877f01    4656

Dell#$n-instance 1 logical-network n 2a8d5d19-8845-4365-

ad04-243f0b6df252

Name : 2a8d5d19-8845-4365-ad04-243f0b6df252

Description :

Tunnel Key : 2

Virtual Extensible LAN (VXLAN)

1491

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments