Dell Networking S6000 System Reference Manual Download

Page: 419 / 1510

Prefixes accepted 2, withdrawn 15 by peer, martian prefixes

ignored 0

Prefixes advertised 0, denied 0, withdrawn 0 from peer

Connections established 1; dropped 0

Last reset never

Local host: 172.16.0.1, Local port: 58145

Foreign host: 172.16.0.2, Foreign port: 179

Dell#

Related
Commands

show ip bgp

— views the current BGP routing table.

show ip bgp next-hop

View all next hops (using learned routes only) with current reachability and flap status. This command

only displays one path, even if the next hop is reachable by multiple paths.

S6000

Syntax

show ip bgp [vrf

vrf-name

] next-hop

Parameters

vrf

vrf-name

Enter the keyword

vrf

followed by the name of the VRF to

view all next hops corresponding to that VRF.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.4.
(0.0)

Added support for VRF.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage
Information

The following describes the

show ip bgp next-hop

command shown in the

following example.

Border Gateway Protocol

419

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands