Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1443 / 1510

background image

vlan-stack protocol-type

Define the stackable VLAN tag protocol identifier (TPID) for the outer VLAN tag (also called the VMAN
tag). If you do not configure this command, Dell Networking OS assigns the value 0x9100.

S6000

Syntax

vlan-stack protocol-type

number

Parameters

number

Enter the hexadecimal number as the stackable VLAN tag.
You may specify both bytes of the 2-byte S-Tag TPID. The
range is from 0 to FFFF. The default is

9100

.

Defaults

0x9100

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.7.0

Introduced on the S4810.

Version 8.2.1.0

Introduced on the E-Series ExaScale. C-Series and S-Series
accept both bytes of the 2-byte S-Tag TPID.

Version 8.2.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the C-Series and S-Series.

E-Series
original
Command

Usage
Information

For specific interoperability limitations regarding the S-Tag TPID, refer to the

Dell

Networking OS Configuration Guide

.

The four characters you enter in the CLI for number are interpreted, as shown in
the following table.

Number

Resulting TPID

1

0x0001

10

0x0010

VLAN Stacking

1443

«
...
1441
1442
1443
1444
1445
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

DUB-H4 - Hub - USB

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: N-Tron Pages: 18

Brand: H3C Pages: 13

Brand: H3C Pages: 207

Brand: H3C Pages: 62

Brand: I-Tech Pages: 27

S5560S-EI Series

Brand: H3C Pages: 37

OfficeConnect WX4400

Brand: 3Com Pages: 528

Brand: NETGEAR Pages: 36

Instant On 1930 24G 4SFP/SFP+l

Brand: Aruba Pages: 48

Brand: GALCO Pages: 22

Brand: Sarowin Pages: 9

Brand: Eaton Pages: 2

Brand: Kramer Pages: 2

Brand: Foxun Pages: 7

Brand: Holley Pages: 2

Brand: CONCORD Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands