Dell Networking S6000 System Page 109 Reference Manual Download

Page: 109 / 1510

Type Ctrl-C to abort.

Sending 5, 100-byte ICMP Echos to 172.31.1.255, timeout is 2

seconds:

Reply to request 1 from 172.31.1.208 0 ms

Reply to request 1 from 172.31.1.216 0 ms

Reply to request 1 from 172.31.1.205 16 ms

Reply to request 5 from 172.31.1.209 0 ms

Reply to request 5 from 172.31.1.66 0 ms

Reply to request 5 from 172.31.1.87 0 ms

Dell#

Example (IPv6)

Dell#ping 100::1

Type Ctrl-C to abort.

Sending 5, 100-byte ICMP Echos to 100::1, timeout is 2 seconds:

!!!!!

Success rate is 100.0 percent (5/5), round-trip min/avg/max =

0/0/0 (ms)

Dell#

reload

Reboot Dell Networking Operating System (OS).

S6000

Syntax

reload [conditional

nvram-cfg-change

]

Parameters

conditional

nvram-cfg-
change

Reload if the condition is true. A configuration change to the
nvram requires a switch reload. To reload the switch, select

nvram-cfg-change

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version 9.1(0.0)

Added ‘conditional’ parameter.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Control and Monitoring

109

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands