Dell Networking S6000 System Page 49 Reference Manual Download

Page: 49 / 1510

To enter ISIS ADDRESS-FAMILY mode:

Verify that you are logged in to ROUTER ISIS mode.

Enter the command

address-family ipv6 unicast

. The prompt changes to include (conf-

router_isis-af_ipv6).

LLDP Mode

To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode. For more information,
refer to

Link Layer Discovery Protocol (LLDP)

To enter LLDP mode:

To enable LLDP globally, verify that you are logged in to CONFIGURATION mode. To enable LLDP

on an interface, verify that you are logged in to INTERFACE mode.

Enter the

protocol lldp

command. The prompt changes to include (conf-lldp) or (conf-if-

interface

-lldp).

LLDP MANAGEMENT INTERFACE Mode

To enable and configure Link Layer Discovery Protocol (LLDP) on management interfaces, use LLDP
MANAGEMENT INTERFACE mode.

To enter LLDP MANAGEMENT INTERFACE mode:

Verify that you are logged in to LLDP mode.

Enter the

management-interface

command. The prompt changes to include (conf-lldp-mgmtIf).

LINE Mode

To configure the console or virtual terminal parameters, use LINE mode.
To enter LINE mode:

Verify that you are logged in to CONFIGURATION mode.

Enter the

line

command. Include the keywords

console

vty

and their line number available on

the switch. The prompt changes to include (config-line-console) or (config-line-vty).

You can exit this mode by using the

exit

command.

MAC ACCESS LIST Mode

To enter MAC ACCESS LIST mode and configure either standard or extended access control lists (ACLs),
use the

mac access-list standard

mac access-list extended

command.

To enter MAC ACCESS LIST mode:

Verify that you are logged in to CONFIGURATION mode.

Use the

mac access-list standard

mac access-list extended

command. Include a

name for the ACL. The prompt changes to include (conf-std-macl) or (conf-ext-macl).

You can return to CONFIGURATION mode by using the

exit

command.

MONITOR SESSION Mode

To enable and configure a traffic monitoring session using port monitoring, use MONITOR SESSION
mode. For more information, refer to

Port Monitoring

CLI Basics

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands