Dell Networking S6000 System Reference Manual Download

Page: 1183 / 1510

Related
Commands

network

— enables RIP.

exit

— returns to CONFIGURATION mode.

show config

Display the changes you made to the RIP configuration. The default values are not shown.

S6000

Syntax

show config

Command
Modes

ROUTER RIP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.6.1.0

Introduced on the C-Series.

pre-Version
6.2.1.1

Introduced on the E-Series.

Example

Dell(conf-router_rip)#show config

router rip

network 172.31.0.0

passive-interface GigabitEthernet 0/1

Dell(conf-router_rip)#

Routing Information Protocol (RIP)

1183

«
...
1181
1182
1183
1184
1185
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands