Dell Networking S6000 System Reference Manual Download Page 900

Page: 900 / 1510

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

Version 7.6.1.0

Introduced on the C-Series.

Version 7.4.1.0

Introduced on the E-Series.

clear lldp neighbors

Clear LLDP neighbor information for all interfaces or a specific interface.

S6000

Syntax

clear lldp neighbors {

interface

}

Parameters

interface

Enter the following keywords and slot/port or number
information:

• For a Fast Ethernet interface, enter the keyword

FastEthernet

then the slot/ port information.

• For a 1-Gigabit Ethernet interface, enter the keyword

GigabitEthernet

followed by the slot/ port

information.

• For a 10-Gigabit Ethernet interface, enter the keyword

tenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

Defaults

none

Command
Modes

EXEC Privilege

Command
History

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

Version 7.6.1.0

Introduced on the C-Series.

900

Link Layer Discovery Protocol (LLDP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Dell Networking S6000 System, Reference Manual, Page: 900 / 1510

Search results

Summary of Contents for Networking S6000 System

Reviews: