Dell Networking S6000 System Page 1397 Reference Manual Download

Page: 1397 / 1510

Parameters

stp-id

Enter zero (0). The switch supports one spanning tree group
with a group ID of 0.

protocol

Enter the keyword for the type of STP to debug, either

mstp

pvst

, or

rstp

all

(OPTIONAL) Enter the keyword

all

to debug all spanning

tree operations.

bpdu

(OPTIONAL) Enter the keyword

bpdu

to debug bridge

protocol data units.

config

(OPTIONAL) Enter the keyword

config

to debug

configuration information.

events

(OPTIONAL) Enter the keyword

events

to debug STP

events.

general

(OPTIONAL) Enter the keyword

general

to debug general

STP operations.

root

(OPTIONAL) Enter the keyword

root

to debug STP root

transactions.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version
6.2.1.1

Introduced on the E-Series.

Usage
Information

When you enable

debug spanning-tree bpdu

for multiple interfaces, the

software only sends information on BPDUs for the last interface specified.

Related
Commands

protocol spanning-tree

— enters SPANNING TREE mode on the switch.

Spanning Tree Protocol (STP)

1397

«
...
1395
1396
1397
1398
1399
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands