Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1429 / 1510

background image

of the far end tunnel peer, rather than to the tunnel destination. This reduces the
chance of both ends of the tunnel staying in keepalive down state. If both ends get
into a keepalive down state that does not clear in a few seconds, then performing
shutdown - no shutdown sequence on one end should bring both ends back to
up.

tunnel allow-remote

Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If

you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted.

This feature is supported on S6000 platforms.

Syntax

tunnel allow-remote

{

ip-address | ipv6-address

} [

mask

]

To delete a configured allow-remote entry use the

no

tunnel allow-remote

command. Any specified address/mask values must match an existing entry for the
delete to succeed. If the address and mask are not specified, this command deletes
all allow-remote entries.

Parameters

ip-address

Enter the source IPv4 address in A.B.C.D format.

ipv6–address

Enter the source IPv6 address in X:X:X:X::X format.

mask

(OPTIONAL) Enter a network mask in /prefix format (/x) or
A.B.C.D to match a range of remote addresses. The default
mask is /32 for IPv4 addresses and /128 for IPv6 addresses,
which match only the specified address.

Defaults

If you do not configure tunnel allow remote , all traffic which is destined to tunnel
source address is decapsulated.

Defaults

By default there are no tunnel allow remote entries.

Command
Modes

INTERFACE TUNNEL

Command
History

Version 9.3(0.1)

Introduced on the S6000 and Z9000.

Version 9.4(0.0)

Introduced on the S4810, S4820T, S6000 and Z9000.

Usage
Information

You can configure up to eight allow-remote entries on any multipoint receive-only
tunnel.

This command fails if the address family entered does not match the outer header
address family of the tunnel mode, tunnel source, or any other tunnel allow-
remote.

Object Missing

1429

«
...
1427
1428
1429
1430
1431
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Hama Pages: 14

Super Speed USB 3.0 Hub

Brand: Hama Pages: 14

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Premium Silver USB 2.0 Hub 1:4

Brand: Hama Pages: 12

Brand: Hama Pages: 18

uRage Vendetta 210

Brand: Hama Pages: 36

Brand: Pathway connectivity solutions Pages: 2

Brand: Brightlink Pages: 33

Brand: N-Tron Pages: 2

IP-Reach IPR-M1

Brand: Raritan Pages: 4

Brand: Dahua Pages: 17

Brand: Edge-Core Pages: 12

Digital Energy STS-400-25-3

Brand: GE Pages: 49

Brand: Abseco Pages: 10

Brand: Conceptronic Pages: 7

Brand: Tenda Pages: 177

MISCOM7220G-4GF-16GT

Brand: Maiwe Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands