Dell Networking S6000 System Reference Manual Download

Page: 606 / 1510

• For a VLAN interface, enter the keyword

vlan

then the

slot/port information. The range is from 1 to 4094.

• For a 1-Gigabit Ethernet interface, enter the keyword

gigabitethernet

followed by the slot/port

information.

• For a 10-Gigabit Ethernet interface, enter the keyword

tengigabitethernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

E-Series legacy
command

Usage
Information

IGMP commands accept

only

non-VLAN interfaces — specifying VLAN does not

yield results.

debug ip igmp

Enable debugging of IGMP packets.

S6000

Syntax

debug ip igmp [

group

address |

interface

]

• To disable IGMP debugging, use the

no debug ip igmp [

group address

interface

]

command.

• To disable all debugging, use the

undebug all

command.

Parameters

group-address

(OPTIONAL) Enter the IP multicast group address in dotted
decimal format.

606

Internet Group Management Protocol (IGMP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands