manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 693 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 693

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on S4810.

Version 8.3.11.1

Introduced on Z9000.

Version 8.1.1.0

Introduced on E-Series ExaScale.

Version 7.6.1.0

Introduced on S-Series.

Version 7.5.1.0

Introduced on C-Series.

pre-Version 
6.2.1.0

Introduced on E-Series.

Usage 
Information

Port Channel interfaces are logical interfaces and can be either in Layer 2 mode (by 
using the 

switchport

 command) or Layer 3 mode (by configuring an IP address). 

You can add a Port Channel in Layer 2 mode to a VLAN.

The 

shutdown

, 

description

, and 

name

 commands are the only commands that 

you can configure on an interface while it is a member of a Port Channel. To add a 
physical interface to a Port Channel, the interface can only have the 

shutdown

, 

description

, and 

name

 commands configured. The Port Channel’s configuration 

is applied to the interfaces within the Port Channel.

A Port Channel can contain both 100/1000 interfaces and GE interfaces. Based on 
the first interface configured in the Port Channel and enabled, Dell Networking OS 
determines if the Port Channel uses 100 Mb/s or 1000 Mb/s as the common speed. 
For more information, refer to 

channel-member

.

If the line card is in a Jumbo mode chassis, you can also configure the 

mtu

 and 

ip 

mtu

 commands. The Link MTU and IP MTU values configured on the channel 

members must be greater than the Link MTU and IP MTU values configured on the 
Port Channel interface.

If the stack—unit card is in a Jumbo mode chassis, you can also configure the 

mtu 

and 

ip mtu

 commands. The Link MTU and IP MTU values configured on the 

channel members must be greater than the Link MTU and IP MTU values 
configured on the Port Channel interface.

NOTE: In a Jumbo-enabled system, all members of a Port Channel must be 
configured with the same link MTU values and the same IP MTU values.

Interfaces

693

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments