Dell Networking S6000 System Reference Manual Download

Page: 907 / 1510

show lldp neighbors

Display LLDP neighbor information for all interfaces or a specified interface.

S6000

Syntax

show lldp neighbors [

interface

] [detail]

Parameters

interface

(OPTIONAL) Enter the following keywords and slot/port or
number information:

• For a Fast Ethernet interface, enter the keyword

FastEthernet

then the slot/ port information.

• For a 1-Gigabit Ethernet interface, enter the keyword

GigabitEthernet

followed by the slot/ port

information.

• For a 10-Gigabit Ethernet interface, enter the keyword

tenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

detail

(OPTIONAL) Enter the keyword

detail

to display all the TLV

information, remote management IP addresses, timers, and
LLDP tx and rx counters.

Defaults

none

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.1.
(0.0)

Modified output of detail parameter to display remote
management IP addresses.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

Version 7.6.1.0

Introduced on the C-Series.

Version 7.4.1.0

Introduced on the E-Series.

Link Layer Discovery Protocol (LLDP)

907

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands