Dell Networking S6000 System Reference Manual Download

Page: 930 / 1510

not part of the mesh-group. However, member X cannot forward the SA message
to other members of the mesh-group.

ip msdp originator-id

Configure the MSDP Originator ID.

S6000

Syntax

ip msdp originator-id {

interface

}

To remove the originator-id, use the

no ip msdp originator-id

{

interface

}

command.

Parameters

interface

Enter the following keywords and slot/port or number
information:

• For a Loopback interface, enter the keyword

loopback

then a number from 0 to 16383.

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a 1-Gigabit Ethernet interface, enter the keyword

GigabitEthernet

then the slot/port information.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a VLAN, enter the keyword

vlan

then a number from

1 to 4094.

Defaults

Not configured.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

930

Multicast Source Discovery Protocol (MSDP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands