Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 1129 / 1510

background image

Version 8.3.7.0

Introduced on the S4810.

Usage
Information

Use this command to specify the name of the output QoS policy. Once output
policy is specified, rate-shape, scheduler strict, bandwidth-percentage, and WRED
can be defined. This command enables the qos-policy-output configuration mode
—(conf-qos-policy-out).

Related
Commands

bandwidth-percentage

— assigns percentage of bandwidth to the class/queue.

— assigns yellow or green drop precedence.

rate-police

Specify the policing functionality on incoming traffic.

S6000

Syntax

rate-police [kbps]

committed-rate

[burst-KB] [peak [kbps]

peak-

rate

[

burst-KB

]]

Parameters

kbps

Enter the keyword

kbps

to specify the rate limit in Kilobits

per second (Kbps). Make the following value a multiple of 64.
The range is from 0 to 40000000. The default granularity is
Megabits per second (Mbps).

committed-
rate

Enter the bandwidth in Mbps. The range is from 0 to 40000.

burst-KB

(OPTIONAL) Enter the burst size in KB. The range is from 16
to 200000. The default is

100

.

peak

peak-rate

(OPTIONAL) Enter the keyword

peak

then a number to

specify the peak rate in Mbps. The range is from 0 to 40000.
The default is the same as designated for

committed-rate

.

Defaults

Burst size is 100KB.

peak-rate

is by default the same as

committed-rate

.

Granularity for

committed-rate

and

peak-rate

is Mbps unless you use the

kbps

option.

Command
Modes

QOS-POLICY-IN

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Quality of Service (QoS)

1129

«
...
1127
1128
1129
1130
1131
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

RackSwitch G8332

Brand: IBM Pages: 18

Brand: 3Com Pages: 8

PathBuilder S200 Series

Brand: 3Com Pages: 11

Brand: 3Com Pages: 8

CoreBuilder 3500

Brand: 3Com Pages: 96

Brand: Camozzi Pages: 2

Brand: BERNSTEIN Pages: 3

Brand: hager Pages: 2

Brand: SMART Pages: 46

Brand: Xantech Pages: 4

Brand: Watt Stopper Pages: 10

Brand: Ruby Tech Pages: 2

Brand: Eaton Pages: 2

Brand: 3Com Pages: 62

Elinx EIR510-2MC-T

Brand: B&B Electronics Pages: 107

Brand: Eaton Pages: 2

Brand: W2IIHY Pages: 28

Brand: Alloy Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands