Dell Networking S6000 System Page 715 Reference Manual Download

Page: 715 / 1510

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.4.10

Introduced on the E-Series.

Example

Dell#debug ip dhcp

00:12:21 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received

at interface 113.3.3.17 BOOTP

Request, hops = 0, XID = 0xbf05140f, secs = 0, hwaddr =

00:60:CF:20:7B:8C, giaddr = 0.0.0.0

00:12:21 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for

00:60:CF:20:7B:8C to 14.4.4.2

00:12:26 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received

at interface 113.3.3.17 BOOTP

Request, hops = 0, XID = 0xbf05140f, secs = 5, hwaddr =

00:60:CF:20:7B:8C, giaddr = 0.0.0.0

00:12:26 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for

00:60:CF:20:7B:8C to 14.4.4.2

00:12:40 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received

at interface 113.3.3.17 BOOTP

Request, hops = 0, XID = 0xda4f9503, secs = 0, hwaddr =

00:60:CF:20:7B:8C, giaddr = 0.0.0.0

00:12:40 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for

00:60:CF:20:7B:8C to 14.4.4.2

00:12:42 : %RELAY-I-PACKET: BOOTP REPLY (Unicast) received at

interface 14.4.4.1 BOOTP Reply,

hops = 0, XID = 0xda4f9503, secs = 0, hwaddr = 00:60:CF:20:7B:

8C, giaddr = 113.3.3.17

00:12:42 : %RELAY-I-BOOTREPLY: Forwarded BOOTREPLY for

00:60:CF:20:7B:8C to 113.3.3.254

00:12:42 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received

at interface 113.3.3.17 BOOTP

Request, hops = 0, XID = 0xda4f9503, secs = 0, hwaddr =

00:60:CF:20:7B:8C, giaddr = 0.0.0.0

00:12:42 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for

00:60:CF:20:7B:8C to 14.4.4.2

00:12:42 : %RELAY-I-PACKET: BOOTP REPLY (Unicast) received at

interface 14.4.4.1 BOOTP Reply,

hops = 0, XID = 0xda4f9503, secs = 0, hwaddr = 00:60:CF:20:7B:

8C, giaddr = 113.3.3.17

00:12:42 : %RELAY-I-BOOTREPLY: Forwarded BOOTREPLY for

00:60:CF:20:7B:8C to 113.3.3.254

Dell#

Related
Commands

ip helper-address

– specifies the destination broadcast or host address for the

DHCP server request.

IPv4 Routing

715

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands