Dell Networking S6000 System Reference Manual Download

Page: 362 / 1510

neighbor add-path

This command allows the specified neighbor/peer group to send/receive multiple path advertisements.

S6000

Syntax

neighbor [

ip-address

peer-group-name

] add-path [send |

receive | both]

path-count

Parameters

ip-address

(OPTIONAL) Enter the IP address of the neighbor in dotted
decimal format.

peer-group-
name

(OPTIONAL) Enter the name of the peer group.

send

Enter the keyword

send

to indicate that the system sends

multiple paths to peers.

receive

Enter the keyword

receive

to indicate that the system

accepts multiple paths from peers.

both

Enter the keyword

both

to indicate that the system sends

and accepts multiple paths from peers.

path-count

Enter the number paths supported. The range is from 2 to
64.

Defaults

none

Command
Modes

CONFIGURATION-ROUTER-BGP-ADDRESS FAMILY

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.8.0

Introduced on the S4810.

Related
Commands

bgp add-path

— allows the advertisement of multiple paths for the same address

prefix without the new paths implicitly replacing any previous ones.

362

Border Gateway Protocol

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands