Dell Networking S6000 System Page 1134 Reference Manual Download

Page: 1134 / 1510

Parameters

ip-dscp

value

(OPTIONAL) Enter the keywords

ip-dscp

then the IP DSCP

value. The range is from 0 to 63.

mac-dot1p

value

Enter the keywords

mac-dot1p

then the dot1p value. The

range is from 0 to 7.

Defaults

none

Command
Modes

CONFIGURATION (conf-qos-policy-in)

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Usage
Information

After the IP DSCP bit is set, other QoS services can then operate on the bit settings.

show qos class-map

View the current class map information.

S6000

Syntax

show qos class-map [

class-name

]

Parameters

class-name

(Optional) Enter the name of a configured class map.

Defaults

none

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

1134

Quality of Service (QoS)

«
...
1132
1133
1134
1135
1136
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands