Enttec Hyperion 71025 User Manual Download

Page: 1 / 22

Hyperion User Manual

51164

For latest version visit:

www.enttec.com

January 19

ID: 3809208

Hyperion

INTELLIGENT GIGABIT SWITCH

Contents

Package Contents .................................................................... 2

Safety Information .................................................................. 2

Initial Setup ............................................................................... 2

Out of Box (Factory Settings) ............................................ 2

Finding IP Address Using NMU v1.9 ................................. 2

Default Login Details .......................................................... 3

Physical Dimensions ............................................................... 3

Specifications ........................................................................... 4

Hyperion Hardware Interface (Front) ................................. 5

LED Status .................................................................................. 5

Hyperion Hardware Interface (Rear) .................................. 5

Application Diagram ............................................................... 6

Ethernet Link Pin Out ............................................................. 6

Redundancy Link ..................................................................... 7

How to Access Web Interface?.............................................. 8

Hyperion Web Interface ......................................................... 9

Home Page ................................................................................ 9

Settings Page .......................................................................... 10

Change Password .............................................................. 10

Ports Page ................................................................................ 11

Link Aggregation .................................................................... 12

Administration ........................................................................ 13

Restore to factory defaults (web interface) ............... 13

Restore to factory defaults (reset button) .................. 14

Reboot .................................................................................. 14

Backup ..................................................................................14

Restore .................................................................................14

Firmware Update................................................................ 15

Tips and Tricks ........................................................................ 17

Hyperion not found by NMU ........................................... 17

Unsuccessful Firmware update, causes white page . 17

Settings do not Save ......................................................... 17

Redundancy Link Doesn’t work

...................................... 17

Connection Lost ................................................................ 18

Device connected to Hyperion, not found ................. 18

Device not discovered on reconnection ..................... 18

Settings for your Computer .............................................19

Steps for Windows 7 ......................................................19

Steps for MacOS ............................................................ 20

Available Models .................................................................... 21

Ordering Information ............................................................ 21

Accessories and Recommended Products....................... 21

Summary of Contents for Hyperion 71025























Search results

Summary of Contents for Hyperion 71025

Reviews:

Related manuals for Hyperion 71025

Brands by name

Popular brands

Enttec Hyperion 71025, User Manual

Search results

Summary of Contents for Hyperion 71025

Reviews:

Related manuals for Hyperion 71025

Brands by name

Popular brands