manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

0B-13 Maintenance and Lubrication: 

WARNING:

With vehicle parked on a fairly steep slope, 
make sure nothing is in the way downhill to 
avoid any personal injury or property 
damage. Be prepared to apply regular brake 
quickly even if vehicle should start to move.

 

Check to ensure that parking brake is fully effective 
when the vehicle is stopped on the safe slope and brake 
lever is pulled all the way.

Steering

• Check to ensure that steering wheel is free from 

instability, or abnormally heavy feeling.

• Check that the vehicle does not wander or pull to one 

side.

Engine

• Check that engine responds readily at all speeds.

• Check that engine is free from abnormal noise and 

abnormal vibration.

Body, Wheels and Power Transmitting System

Check that body, wheels and power transmitting system 
are free from abnormal noise and abnormal vibration or 
any other abnormal condition.

Meters and Gauge

Check that speedometer, odometer, fuel meter, 
temperature gauge, etc. are operating accurately.

Lights

Check that all lights operate properly.

Windshield Defroster

Periodically check that air comes out from defroster 
outlet when operating heater or air conditioning.
Set mode control lever to defroster position and fan 
switch lever to “HI” position for this check.

Specifications

Tightening Torque Specifications

S4RS0A0207001

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

Special Tools and Equipment

Recommended Fluids and Lubricants

S4RS0A0208001

Special Tool

S4RS0A0208002

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Engine oil drain plug

35

3.5

25.5

)

Oil filter

14

1.4

10.5

(for reference) 

)

Engine oil

SG, SH, SJ or SL grade (Refer to “Engine Oil and Filter Change: ” for engine oil 
viscosity.)

Engine coolant
(Ethylene glycol base coolant)

“Antifreeze/Anticorrosion coolant”

Brake fluid

DOT 3 or SAE J1703

Manual transaxle oil

Refer to “Manual Transaxle Oil Change:  in Section 5B”.

Automatic transaxle fluid

Refer to “A/T Fluid Change:  in Section 5A”.

Door hinges

Engine oil or water resistance chassis grease

Hood latch assembly

Engine oil or water resistance chassis grease

Key lock cylinder

Spray lubricant

09915–47331
Oil filter wrench

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
Dakota Digital Retrotech RTX-68D-CHG Quick Start Manual preview
Retrotech RTX-68D-CHG
Бренд: Dakota Digital Страницы: 4
Masterack RM470057 Assembly Instructions preview
RM470057
Бренд: Masterack Страницы: 4
Over Armour Offroad KAW-SX-SDK01 Instructions For Installation And Care preview
KAW-SX-SDK01
Бренд: Over Armour Offroad Страницы: 5
Kia Sorento Owner'S Manual preview
Sorento
Бренд: Kia Страницы: 51
aci ADARAC Aluminum M Series Installation Instructions Manual preview
ADARAC Aluminum M Series
Бренд: aci Страницы: 16
Imiola HAK-POL O/018 Quick Manual preview
O/018
Бренд: Imiola HAK-POL Страницы: 3
Scion 2012 iQ Quick Reference Manual preview
2012 iQ
Бренд: Scion Страницы: 24
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Бренд: Car-Systems Страницы: 10
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Бренд: FVC Страницы: 8
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
WABCO TP19039 Manual preview
TP19039
Бренд: WABCO Страницы: 34
Webasto Telestart T70 Installation Instructions Manual preview
Telestart T70
Бренд: Webasto Страницы: 23
Toro Security Cage Kit Installation Instructions Manual preview
Security Cage Kit
Бренд: Toro Страницы: 8
Mopar 82214480 Manual preview
82214480
Бренд: Mopar Страницы: 17
Toyota 4Runner 1999 Owner'S Manual preview
4Runner 1999
Бренд: Toyota Страницы: 285
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Belkin F8J034 User Manual preview
F8J034
Бренд: Belkin Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды