manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Instrumentation / Driver Info. / Horn:  9C-12

Oil Pressure Switch Removal and Installation

S4RS0A9306006

For removal and installation, refer to “Oil Pressure 
Check:  in Section 1E”.

Oil Pressure Switch Inspection

S4RS0A9306007

1) Disconnect oil pressure switch (1) lead wire.
2) Check for continuity between oil pressure switch 

terminal (2) and cylinder block (3) as shown.
If check result is not as specified, replace oil 
pressure switch (1).

Oil pressure sensor specification
During engine running: No continuity
At engine stop: Continuity

VSS Removal and Installation

S4RS0A9306008

For removal and installation, refer to “Vehicle Speed 
Sensor (VSS) Removal and Installation:  in Section 5B” 
or “Output Shaft Speed Sensor (VSS) Removal and 
Installation:  in Section 5A”.

VSS Inspection

S4RS0A9306009

Refer to “Vehicle Speed Sensor (VSS) Inspection (M/T 
model):  in Section 1C” or “Output Shaft Speed Sensor 
(VSS) Inspection:  in Section 5A”.

Engine Coolant Temperature (ECT) Sensor 
Inspection

S4RS0A9306010

Check engine coolant temperature sensor for resistance, 
refer to “Engine Coolant Temperature (ECT) Sensor 
Inspection:  in Section 1C”.

Brake Fluid Level Switch Inspection

S4RS0A9306011

Check for continuity between terminals of brake fluid 
level switch coupler (1). If found defective, replace 
switch.

Brake fluid level switch specification
OFF position (float up): No continuity
ON position (float down): Continuity

1. Fuel pump
2. Float

4. Engine oil filter

F: Front

“a”

“b”

1

“c”

“d”

2

2

I4RH01930003-

I3RM0A930009-

1

I4RS0A930013-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Бренд: CITROEN Страницы: 2
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Бренд: RAM Страницы: 16
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
Axxess AX-DSPX-HYKIA2 Installation Instructions preview
AX-DSPX-HYKIA2
Бренд: Axxess Страницы: 4
Vintage Air 473275 Manual preview
473275
Бренд: Vintage Air Страницы: 14
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Бренд: hc-cargo Страницы: 60
B-Speech Sima User Manual preview
Sima
Бренд: B-Speech Страницы: 4
Sears 580.32601 Owner'S Manual preview
580.32601
Бренд: Sears Страницы: 41
Tellur BASIC TLL171231 User Manual preview
BASIC TLL171231
Бренд: Tellur Страницы: 5
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6
Camecho R0009 Instructions preview
R0009
Бренд: Camecho Страницы: 2
Eibach E60-82-007-02-10 Installation Instructions preview
E60-82-007-02-10
Бренд: Eibach Страницы: 3
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Бренд: Rugged Ridge Страницы: 3
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Бренд: SilverLeaf Electronics Страницы: 16
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Бренд: Anker Technology Страницы: 8
Volvo S90 - ACCESSORY PANEL Owner'S Manual Supplement preview
S90 - ACCESSORY PANEL
Бренд: Volvo Страницы: 166
Fiat 500L 2020 Owner'S Manual preview
500L 2020
Бренд: Fiat Страницы: 284
Classic AutoAir Mustang 1969 Installation Manual preview
Mustang 1969
Бренд: Classic AutoAir Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды