manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Fuel System:  1G-16

Fuel Pump Inspection

S4RS0A1706021

• Check fuel pump assembly for damage.
• Check fuel suction filter (1) for evidence of dirt and 

contamination.
If present, replace or clean and check for presence of 
dirt in fuel tank.

• For electrical circuit, refer to “Fuel Pressure Check:  in 

Section 1A”.

• For inspection of fuel level gauge (2), refer to “Fuel 

Level Sensor Inspection:  in Section 9C”.

Specifications

Tightening Torque Specifications

S4RS0A1707001

NOTE:
The specified tightening torque is also described in the following.
“Fuel System Components: ”
“Fuel Hose Disconnecting and Reconnecting: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

I3RM0A170024-

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Fuel delivery pipe bolt

25

2.5

18.0

)

Fuel tank bolt

50

5.0

36.5

)

Fuel filler hose clamp

2

0.2

1.5

)

Fuel pump assembly bolt

11

1.1

8.0

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Parrot CK3300 Setup Information Manual preview
CK3300
Бренд: Parrot Страницы: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Бренд: Parrot Страницы: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Бренд: Parrot Страницы: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Бренд: Parrot Страницы: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Бренд: Parrot Страницы: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Бренд: Parrot Страницы: 106
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Бренд: Mazda Страницы: 400
Quadratec 12057.0263 Installation Manual preview
12057.0263
Бренд: Quadratec Страницы: 12
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
Racelogic Speed & Route Profiler Manual preview
Speed & Route Profiler
Бренд: Racelogic Страницы: 24
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
Honda 2007 Fit User Information preview
2007 Fit
Бренд: Honda Страницы: 24
Brigade VBV-770-310 Quick Installation Manual preview
VBV-770-310
Бренд: Brigade Страницы: 12
SSV Works RG4-DM3 Manual preview
RG4-DM3
Бренд: SSV Works Страницы: 2
Subaru S0A367010 Installation Instructions preview
S0A367010
Бренд: Subaru Страницы: 2
MacNeil Pet Barrier Instruction Manual preview
Pet Barrier
Бренд: MacNeil Страницы: 2
EUFAB 16559 Operating Instructions Manual preview
16559
Бренд: EUFAB Страницы: 12
travall TDG1166 Fitting Instructions preview
TDG1166
Бренд: travall Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды