manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Bag System:  8B-5

• Make sure air bag system grounding point (2) is clean 

and ground is securely fastened for optimum metal-to-
metal contact. Poor grounding can cause intermittent 
problems that are difficult to diagnose.

Precautions on Disposal of Air Bag and Seat 
Belt Pretensioner

S4RS0A8200003

Do not dispose of the live (undeployed) air bag (inflator) 
modules and the live (inactivated) seat belt 
pretensioners.
When disposal is necessary, be sure to deploy / activate 
the air bag and seat belt pretensioner according to 
deployment / activation procedure described in “Air Bag 
(Inflator) Module and Seat Belt Pretensioner Disposal: ”.

WARNING:

Failure to follow proper air bag (inflator) 
module and seat belt pretensioner disposal 
procedures can result in air bag deployment 
and pretensioner activation which could 
cause personal injury. Undeployed air bag 
(inflator) module and inactivated seat belt 
pretensioner must not be disposed of 
through normal refuse channels.
The undeployed air bag (inflator) module and 
inactivated seat belt pretensioner contain 
substances that can cause severe illness or 
personal injury if the sealed container is 
damaged during disposal.

 

General Description

Air Bag System Construction

S4RS0A8201001

With the air bag system which includes front air bags, 
side curtain-air bag and side-air bags for both the 
driver’s and passenger’s sides as well as the seat belt 
pretensioners, the sag of the seat belt is taken up (for 
seat belt with pretensioner), the driver air bag (inflator) 
module is deployed from the center of the steering 
column and the passenger air bag (inflator) module from 
the top of the instrument panel in front of the front 
passenger seat in occurrence of a front collision with an 
impact larger than a certain set value to supplement 
protection offered by the driver and front passenger seat 
belts.
Side-air bag (inflator) module is deployed from the side 
of the seat back in occurrence of a sideward collision 
with an impact larger than a certain set value.
Side curtain-air bag (inflator) module is deployed from 
the roof side in occurrence of a sideward collision with 
an impact larger than a certain set value.

1

2

3

4

5

I4RS0A820004-

1. Driver air bag

4. Side-air bag

2. Passenger air bag

5. Side curtain-air bag

3. Seat belt pretensioner

I4RS0A820102-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Camcar 2155 Fitting Instructions preview
2155
Бренд: Camcar Страницы: 2
Camcar 40000 Manual preview
40000
Бренд: Camcar Страницы: 6
Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Бренд: Uniden Страницы: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Бренд: Uniden Страницы: 20
Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Бренд: Yakima Страницы: 8
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Roav R5141 Owner'S Manual preview
R5141
Бренд: Roav Страницы: 10
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Бренд: RAM Страницы: 16
Mercedes-Benz R 350 2012 Operator'S Manual preview
R 350 2012
Бренд: Mercedes-Benz Страницы: 368
BMW E46/2 Coupe Manual preview
E46/2 Coupe
Бренд: BMW Страницы: 55
Whispbar K496W Fitting Instructions Manual preview
K496W
Бренд: Whispbar Страницы: 15
JKS OGS125 Installation Instructions preview
OGS125
Бренд: JKS Страницы: 3
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Бренд: Lit Lightz Страницы: 3
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Бренд: U.S. General Страницы: 8
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Бренд: Vauxhall Страницы: 131
AIS MAZMOD2 Manual preview
MAZMOD2
Бренд: AIS Страницы: 2
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Бренд: Honda Страницы: 124
Bestop 51252 Installation Instructions preview
51252
Бренд: Bestop Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды