manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Conditioning System:  7B-26

Installation

Reverse the removal procedure noting the following 
instruction.
• Install evaporator thermistor (evaporator temperature 

sensor) (1) onto evaporator (2) as shown.

Evaporator Thermistor (Evaporator 
Temperature Sensor) Inspection

S4RS0A7206014

Check resistance between terminals of evaporator 
thermistor (1).
If check results are as not specified, replace evaporator 
thermistor.

Evaporator themistor resistance
0 

q

C (32 

q

F): 6.6 – 6.9 k

:

25 

q

C (77 

q

F): 1.9 – 2.3 k

:

Expansion Valve Removal and Installation

S4RS0A7206015

Removal

1) Recover refrigerant from the A/C system with 

recovery and recycling equipment referring to 
“Recovery” in “Operation Procedure for Refrigerant 
Charge: ”.

2) Loosen a bolt (1) and remove pipes from expansion 

valve (2).

3) Loosen bolts (3) and remove expansion valve.

3. 50 

r

 5 mm (2 

r

 0.2 in.)

4. Sensor part fixed to 10th fin from the bottom
5. Holding part fixed to 8th fin from the bottom

1

I4RS0A720052-

5

1

4

2

3

I4RS0A720053-

[A]: Resistance (k

:

)

[B]: Temperature

I4RS0A720027-

1

2

2

3

I4RS0A720028-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Бренд: VEAP SHIELD UNITED Страницы: 3
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Бренд: hager Страницы: 9
Ultra Start KE-6 Owner'S Manual preview
KE-6
Бренд: Ultra Start Страницы: 8
AA Products SR-A260 Instruction Manual preview
SR-A260
Бренд: AA Products Страницы: 4
Van Guard VG273 Fitting Instructions preview
VG273
Бренд: Van Guard Страницы: 3
Mazda 2006 RX-8 Service Highlights preview
2006 RX-8
Бренд: Mazda Страницы: 122
BMW 323Ci Manual preview
323Ci
Бренд: BMW Страницы: 189
Reese Explore 63153 Instruction Manual preview
63153
Бренд: Reese Explore Страницы: 9
Draw tite 24963 Installation Instructions preview
24963
Бренд: Draw tite Страницы: 4
EFILive CM2350B User Manual preview
CM2350B
Бренд: EFILive Страницы: 25
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Бренд: Fisher Body Страницы: 37
Manik 519952T Installation Instructions preview
519952T
Бренд: Manik Страницы: 2
Edelbrock 2917 Nstallation Instructions preview
2917 Nstallation
Бренд: Edelbrock Страницы: 1
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Бренд: Havis-Shields Страницы: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Бренд: PEUGEOT Страницы: 107
Rigid Hitch BULL BAR Installation Instructions preview
BULL BAR
Бренд: Rigid Hitch Страницы: 2
Lock'er Down 2011 X Instructions preview
2011 X
Бренд: Lock'er Down Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды