manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Wipers / Washers:  9D-4

Windshield Wiper Removal and Installation

S4RS0A9406012

Removal

1) Disconnect negative (–) cable at battery.
2) Remove wiper pivot caps (1) and wiper arm nuts (2), 

and remove windshield wiper arms with wiper blades 
(3).

3) Remove cowl top garnish referring to “Cowl Top 

Components:  in Section 9K”.

4) Disconnect coupler from windshield wiper motor.
5) Remove bolts (1), and remove windshield wiper 

assembly (2).

Installation

1) Install windshield wiper assembly (1), and tighten 

bolts to specified torque.

Tightening torque
Windshield wiper bolt (a):  8 N·m (0.8 kg-m, 6.0 
lb-ft)

2) Connect coupler to windshield wiper motor.

3) Install cowl top garnish referring to “Cowl Top 

Components:  in Section 9K”.

4) Install windshield wiper arms with wiper blades (1) to 

specified position as shown in figure, and then 
tighten windshield wiper nuts to specified torque.

Tightening torque
Windshield wiper arm nut (a):  16 N·m (1.6 kg-m, 
11.5 lb-ft)

5) Install wiper pivot caps (2) to windshield wiper arm 

nuts

6) Connect negative (–) cable to battery.

Windshield Wiper Motor Inspection

S4RS0A9406004

NOTE:
Make sure that battery voltage is 12 V or 
more.

 

1) Disconnect negative (–) cable at battery.
2) Remove windshield wiper arms with wiper blades 

referring to “Windshield Wiper Removal and 
Installation: ”.

3) Remove cowl top garnish referring to “Cowl Top 

Components:  in Section 9K”.

4) Disconnect coupler from windshield wiper motor.
5) Reinstall windshield wiper arms with wiper blade. For 

details, refer to Step 4) of “Installation” in “Windshield 
Wiper Removal and Installation: ”.

6) Check windshield wiper motor for operation as 

follows
• For motor operation in low speed

a. Connect battery positive (+) terminal to 

terminal “1” and its negative (–) terminal to 
terminal “5”.

b. Check if wiper arm reciprocation speed is as 

specification. If check result is not as 
specified, replace motor.

Specification
41 – 51 r/min (rpm)

1

3

3

2

I4RS0A940006-

I4RS0A940007-

I4RS0A940008-

3. Ceramic line
4. Wiper blade center

2

2

3

3

4

1

1

(a)

I4RS0A940009-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Бренд: iDataLink Страницы: 99
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Atera 022 681 Manual preview
022 681
Бренд: Atera Страницы: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Бренд: RAM Страницы: 7
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Бренд: RAM Страницы: 76
Advantech TREK-550 Manual preview
TREK-550
Бренд: Advantech Страницы: 59
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Бренд: GMC Страницы: 120
Prime Tech H-066 User Manual preview
H-066
Бренд: Prime Tech Страницы: 6
Volvo B13R Driver'S Handbook Manual preview
B13R
Бренд: Volvo Страницы: 24
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Бренд: I.D. Systems Страницы: 41
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Бренд: SilverLeaf Electronics Страницы: 16
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
Bulldog Security BulldogOne BD1 User Manual preview
BulldogOne BD1
Бренд: Bulldog Security Страницы: 7
Gigaware Gigaware 12-493 User Manual preview
Gigaware 12-493
Бренд: Gigaware Страницы: 8
Honda 1993 Civic Coupe Owner'S Manual preview
1993 Civic Coupe
Бренд: Honda Страницы: 201
Stanley GLPS Instruction Manual preview
GLPS
Бренд: Stanley Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды