manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4E-29 ABS: 

Installation

1) Check that no foreign material is attached to sensor 

(1) and sensor ring (2).

2) Install it by reversing removal procedure.

Tightening torque
Front wheel speed sensor bolt (a):  25 N·m (2.5 
kg-m, 18.0 lb-ft)
Front wheel speed sensor harness clamp bolt  
(b):  11 N·m (1.1 kg-m, 8.0 lb-ft)

CAUTION:

Do not pull or twist wire harness more than 
necessary when installing front wheel speed 
sensor.

 

3) Check that there is no clearance between sensor 

and knuckle.

Front Wheel Speed Sensor Inspection

S4RS0A4506007

• Check sensor for damage.
• Measure resistance of sensor.

Between both terminals (1) of sensor
1.2 – 1.6 k

:

 at 20 

q

C (68 

q

F)

Between sensor terminal (1) and sensor body (2)
Infinity (

f

)

If the check result is not as specified and any 
malcondition is found, replace.

Rear Wheel Speed Sensor On-Vehicle 
Inspection

S4RS0A4506008

Output Voltage Inspection

1) Disconnect connector from rear wheel speed sensor 

referring to Step 1) to 4) of “Rear Wheel Speed 
Sensor Removal and Installation: ”.

2) Hoist vehicle.
3) Connect voltmeter between connector (1) terminals.
4) While turning wheel at a speed of approximately 3/4 

to 1 1/4 rotation per second, check AC voltage of 
sensor.

Output AC voltage at 3/4 to 1 1/4 rotation per 
second 
53 mV or more

5) If measured voltage is not as specified, check 

sensor, ring and their installation conditions.

[A]: OK
[B]: NG

[A]

[B]

1

1

(a)

(b)

1

2

I4RS0A450026-

I2RH01450052-

I3RH01450049-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Wallbox Commander 2 Installation And User Manual preview
Commander 2
Бренд: Wallbox Страницы: 7
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Бренд: GReddy Страницы: 9
MAcarbon Ferrari 360 Map Carbon Light Installation Instructions preview
Ferrari 360 Map Carbon Light
Бренд: MAcarbon Страницы: 4
Flash Cover MN002 Installation Manual preview
MN002
Бренд: Flash Cover Страницы: 2
Gacell SLH 27C User Manual preview
SLH 27C
Бренд: Gacell Страницы: 25
Kia 2015 optima Quick Start Manual preview
2015 optima
Бренд: Kia Страницы: 5
TIS TISPLUS User Manual preview
TISPLUS
Бренд: TIS Страницы: 6
A-Tach Mounts 50321 Quick Start Manual preview
50321
Бренд: A-Tach Mounts Страницы: 2
Thule 2087 Parts List preview
2087
Бренд: Thule Страницы: 1
Nav TV MOST-HUR MB User Manual preview
MOST-HUR MB
Бренд: Nav TV Страницы: 6
Lexus 2014 GX 460 Quick Manual preview
2014 GX 460
Бренд: Lexus Страницы: 94
AdvanceTec AT6538A Installation Manual preview
AT6538A
Бренд: AdvanceTec Страницы: 8
AdvanceTec Hands free User Manual preview
Hands free
Бренд: AdvanceTec Страницы: 12
AdvanceTec AT6701A User Manual preview
AT6701A
Бренд: AdvanceTec Страницы: 12
Metra Electronics XIAH-FD4 Installation Instructions preview
XIAH-FD4
Бренд: Metra Electronics Страницы: 2
Volkswagen 1999 Golf Diagnostic Manual preview
1999 Golf
Бренд: Volkswagen Страницы: 225
Toyota PRIUS 50 2020 Series Owner'S Manual preview
PRIUS 50 2020 Series
Бренд: Toyota Страницы: 551
Hama DVD Travel Automotive Operating Instructions preview
DVD Travel Automotive
Бренд: Hama Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды