Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 117

Страница: 117 / 1257

Engine General Information and Diagnosis: 1A-69

ECM voltage check

1) Disconnect connector from MAF and IAT sensor with

ignition switch turned OFF.

2) Check for proper connection to MAF and IAT sensor at

“BLK/YEL” and “ORN” wire terminals.

3) If OK, then turn ON ignition switch, measure voltage

between “BLK/YEL” wire terminal of MAF and IAT
sensor connector (1) and vehicle body ground.

Is voltage about 4 – 6 V?

Go to Step 6.

Go to Step 4.

IAT short circuit check

1) Disconnect connectors from ECM with ignition switch

turned OFF.

2) Measure resistance between “BLK/YEL” wire terminal of

MAF and IAT sensor connector and vehicle body
ground.

Is resistance infinity?

Go to Step 5.

“BLK/YEL” wire is
shorted to ground
circuit.
If wire is OK, substitute
a known-good ECM and
recheck.

IAT short circuit check

1) Turn ON ignition switch.
2) Measure voltage between “BLK/YEL” wire terminal of

MAF and IAT sensor connector and vehicle body
ground.

Is voltage about 0 V?

Go to Step 6.

“BLK/YEL” wire is
shorted to other circuit.
If wire is OK, substitute
a known-good ECM and
recheck.

IAT sensor for performance check

1) Check IAT sensor according to “Mass Air Flow (MAF)

and Intake Air Temperature (IAT) Sensor Inspection: in
Section 1C”.

Is it in good condition?

Substitute a known-
good ECM and recheck.

Replace MAF and IAT
sensor.

Step

Action

Yes

I4RS0A110023-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды