Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 583 | Manualshive

Страница: 583 / 1257

background image

Automatic Transmission: 5A-43

DTC P0705: Transmission Range Sensor Circuit Malfunction

S4RS0A5104021

Wiring Diagram

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTCs in TCM memory by using scan tool.
3) Start engine and shift select lever to “D” range.
4) Keep engine running at idle speed for 25 seconds or more.
5) Stop vehicle and check DTC.

DTC Troubleshooting

3

Brake light switch signal inspection

1) With ignition switch ON, check voltage between terminal

“E23-20” of ECM connector and ground.

Brake light switch signal specification
Brake pedal is released: 0 – 1 V
Brake pedal is depressed: 8 – 14 V

Is result as specified?

Substitute a known-
good TCM and recheck.

Mis-adjusted brake light
switch, faulty brake light
switch.
If OK, substitute a
known-good TCM and
recheck.

Step

Action

Yes

No

1. TCM

3. Backup lamp

2. Transmission range sensor

[A]: Terminal arrangement of TCM connector (viewed from harness side)

DTC detecting condition

Trouble area

Multiple or more signals are inputted simultaneously for 12
seconds.

• Select cable maladjusted
• Transmission range sensor (switch) maladjusted
• Transmission range sensor (switch) or its circuit

malfunction

• TCM

2

P

R

N

D

2

L

3

1

PNK/BLK

RED

GRN

GRN/ORN

GRN/YEL

IG11

RED/BLK

LT GRN/BLK

C35-20

C35-1

C35-8

C35-7

C35-19

C35-18

C34

20 19

8 7

18

1

C35

[A]

I4RS0A510010-

Step

Action

Yes

No

1

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System
Check: ”.

2

Do you have SUZUKI scan tool?

Go to Step 3.

Go to Step 4.

«
...
581
582
583
584
585
...
»

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

HOIST-A-TOP JL CRANK

Бренд: Lange Originals Страницы: 13

Бренд: Whispbar Страницы: 14

Бренд: Whispbar Страницы: 15

Бренд: Warn Страницы: 5

Бренд: Unex Страницы: 30

Бренд: Aries Страницы: 5

Бренд: Mercedes-Benz Страницы: 354

Бренд: ICON Страницы: 4

Бренд: Elinchrom Страницы: 101

THERAPEDIC 2000

Бренд: Columbia Страницы: 14

Бренд: Rugged Ridge Страницы: 2

Бренд: Audi Страницы: 63

FABIA II TMB PS 035

Бренд: Skoda Страницы: 16

Бренд: QA1 Страницы: 3

Airgo Active cushion / Comfort

Бренд: TOGU Страницы: 2

Auto-Dimming Mirror

Бренд: Mazda Страницы: 2

Бренд: Conrad Страницы: 8

Бренд: Vauxhall Страницы: 215

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды