manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

7B-23 Air Conditioning System: 

Installation

Reverse the removal procedure to install condenser 
noting the following instructions.
• Replenish specified amount of compressor oil to 

compressor suction side referring to “Replenishing 
Compressor Oil” in “Operation Procedure for 
Refrigerant Charge: ”.

• Evacuate and charge the A/C system referring to 

“Evacuation” and “Charge” in “Operation Procedure 
for Refrigerant Charge: ”.

Desiccant Removal and Installation

S4RS0A7206009

Removal

1) Remove condenser assembly referring to 

“Condenser Assembly Removal and Installation: ”.

2) Remove cap (1) from receiver/dryer tank.
3) Remove desiccant (2) from receiver/dryer tank.

Installation

Reverse the removal procedure noting the following 
instructions.
• Replenish specified amount of compressor oil to 

compressor suction side referring to in “Operation 
Procedure for Refrigerant Charge: ”.

• Do not remove desiccant from the plastic bag until just 

before inserting it into the receiver.

• Install the desiccant with its welded part downward.
• Apply compressor oil to cap’s O-ring.
• Tighten cap to the specified torque

Tightening torque
Cap (a):  3.0 N·m (0.3 kg-m, 2.5 lb-ft)

• Evacuate and charge the A/C system referring to 

“Evacuation” and “Charge” in “Operation Procedure 
for Refrigerant Charge: ”.

2

1

I4RS0A720019-

(a)

I4RS0A720020-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

RaceChip XLR User Manual preview
XLR
Бренд: RaceChip Страницы: 20
Yakima Q46 Installation Instructions preview
Q46
Бренд: Yakima Страницы: 4
Code 3 WingMan Installation & Operation Manual preview
WingMan
Бренд: Code 3 Страницы: 8
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
Maserati Quattroporte Automatic Owner'S Manual preview
Quattroporte Automatic
Бренд: Maserati Страницы: 272
Metra Electronics 95-8202 Installation Instructions Manual preview
95-8202
Бренд: Metra Electronics Страницы: 20
Caraudio-Systems v.LOGiC Intelligent Solution V5-NTG46 Manual preview
v.LOGiC Intelligent Solution V5-NTG46
Бренд: Caraudio-Systems Страницы: 18
JKS JKSOGS960 Installation Instructions Manual preview
JKSOGS960
Бренд: JKS Страницы: 6
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Бренд: Mazda Страницы: 3
Reimo TOUR EASY 4 936550 Quick Start Manual preview
TOUR EASY 4 936550
Бренд: Reimo Страницы: 4
Husky 31564 Assembly, Installation, Operation And Maintenance Instructions preview
31564
Бренд: Husky Страницы: 8
Kolpin 1466 Product Instructions preview
1466
Бренд: Kolpin Страницы: 6
Mercedes-Benz W211 Manual preview
W211
Бренд: Mercedes-Benz Страницы: 27
Jacob Jensen Electronic Parking Disc 3 User Manual preview
Electronic Parking Disc 3
Бренд: Jacob Jensen Страницы: 17
Adaptiv Mini CAM-MB6-AD User Manual preview
CAM-MB6-AD
Бренд: Adaptiv Mini Страницы: 4
Chrysler DODGE AD100 1993 Service Manual preview
DODGE AD100 1993
Бренд: Chrysler Страницы: 1502
TERAFLEX 1365000 Manual preview
1365000
Бренд: TERAFLEX Страницы: 18
Automotive Data Solutions BLADE-AL-TL5-EN Install Manual preview
BLADE-AL-TL5-EN
Бренд: Automotive Data Solutions Страницы: 27

Бренды по названию

Популярные бренды

Загрузить еще бренды